Ligowave LigoBase 5-N, High Performance BaseStation, N-Type connectors for external antenna
Ligowave LigoBase 5-N, LW-PTMP-5-N-BS - High Performance 5Ghz, BaseStation unit, 31 dBm output power, delivers up to 600+ Mbps throughput via W-Jet V wireless protocol, 2.4Ghz access radio, POE-IN, POE-out, 2x N-Type Connectors for external antenna
LigoPTMP series point to multipoint system delivers 600+ Mbps throughput via its unique and powerful RF design that supports up to 256QAM modulation and 31 dBm output power. 1.2 GHz dedicated CPU ensures swift data processing and high packet per second rate (PPS) which is important for real time data transmission applications. Equipped with two Gigabit Ethernet ports, one with PoE passthrough, the unit allows powering and connecting two devices on the tower (another LigoBASE or IP camera). LigoBASE incorporates integrated surge and ESD protection according to IEC standards passing Class 4 requirements. Additionally, weatherproof IP-67 standard rated enclosure design allows using the equipment in any climate conditions.
The full featured operating system makes LigoPTMP devices ideal not only for WISPs and operators, but also for security, enterprise or industrial applications. Proprietary
data transmission protocol (W-Jet V) ensures smooth performance even in noisy areas at the same time delivering high capacity, low latency and high packet per second rate. QoS (quality of service) mechanism allows prioritizing mission critical data and efficiently transmitting voice, video or other real time data over the wireless network. Essential tools like spectrum analyzer, site survey, antenna alignment and others are included.
Easy pre-configuration and maintenance - A new approach to setting up and maintaining your network
Setup Wizard - Guides the installer through the important steps of the set-up process.
Single side configuration - Link parameters are automatically applied to subscriber units once set on the base-station side.
Spectrum analyzer - Demonstrates the current noise floor in a waveform and waterfall graphs.
2.4 GHz access radio - An internal 2.4 GHz radio allows access into the LigoBASE GUI by wireless connection with any WIFI equipped device.
Multiple options to pre-configure LigoPTMP devices are available. Devices can be connected with each other using wired or wireless connectivity. End-user device can also connect to the LigoBASE device using 2.4 GHz access radio or using wire to the Ethernet port of the LigoBASE device. LigoPTMP devices can be discovered using Bonjour, CDP and SSDP protocols as well.
Wireless protocol: W-Jet V
Radio mode: MIMO 2x2
Frequency range: 4.900 - 6.100 GHz (FCC: 4.940 - 4.990 GHz, 5.150-5.250 GHz, 5.725-5.850 GHz)
Channel size: 5, 10, 20, 40, 80 MHz
Modulation schemes: OFDM (256-QAM, 64-QAM, 16-QAM, QPSK, BPSK)
Data rates @ 80 MHz: 866, 780, 650, 585, 520, 390, 260, 195, 130, 65 Mbps
Duplexing scheme: TDD
Error correction: BCC, LDPC
LigoBASE 5-N: 2x N-type connectors
First Interface: 10/100/1000 Base-T with PoE IN (RJ-45)
Second Interface: 10/100/1000 Base-T with PoE OUT (RJ-45)
LigoBASE 5-N Length: 399 mm (15.7‘’), width 174 mm (6.8‘’), height 47 mm (1.8‘’)
Mount length till pole: 124 mm (4.8‘’)
Weight including mount: 3 kg (6.6 lb)
Power input method, voltage: PoE 802.3af, isolated 42 - 57 VDC
Power consumption (max): 8.6 W
Power output method, voltage: PoE 802.3af, 48 VDC, 12.95W maximum
PoE inserter and AC/DC adapter are included
Operating temperature: -40°C (-40 F) ~ +65°C (+149 F)
Humidity: 0 ~ 90 % (non-condensing)
• Wizard for fast link setup
• Centralized control from LigoBASE: A) Common wireless link parameters; B) Individual LigoSU parameters
• Smart Auto-channel
• Robust data security
• QoS with hardware acceleration
• Spectrum analyzer
• Wireless signal and device state indication on RGB LEDs
• Dual firmware image
Dedicated 2.4 GHz radio for management
System monitoring: SNMP, GUI/HTTP(S), Shell/SSH and WNMS
System configuration: GUI/HTTP(S) and WNMS